#   T-H Marine 12V 10A Adjustable Automatic Livewell Pump Timer Control Panel   RWB6942

     [Previous](#)[Previous](#) [![RWB6942](https://www.rhsboating.com.au/images/com_hikashop/upload/thumbnails/300x300/RWB6942.jpg "T-H Marine 12V 10A Adjustable Automatic Livewell Pump Timer Control Panel")](https://www.rhsboating.com.au/images/com_hikashop/upload/RWB6942.jpg "T-H Marine 12V 10A Adjustable Automatic Livewell Pump Timer Control Panel")

 [Next](#)[Next](#)

   [![RWB6942](https://www.rhsboating.com.au/images/com_hikashop/upload/thumbnails/300x300/RWB6942.jpg "T-H Marine 12V 10A Adjustable Automatic Livewell Pump Timer Control Panel")](https://www.rhsboating.com.au/images/com_hikashop/upload/RWB6942.jpg "T-H Marine 12V 10A Adjustable Automatic Livewell Pump Timer Control Panel")[![t-h-marine-logo](https://www.rhsboating.com.au/images/com_hikashop/upload/thumbnails/300x300/chatgpt_image_sep_24_2026_09_02_48_am.jpg "T-H Marine 12V 10A Adjustable Automatic Livewell Pump Timer Control Panel")](https://www.rhsboating.com.au/images/com_hikashop/upload/chatgpt_image_sep_24_2026_09_02_48_am.jpg "T-H Marine 12V 10A Adjustable Automatic Livewell Pump Timer Control Panel")

    $291.17  each

            Brand: [T-H Marine Boat Catches, Hardware & Scuppers](https://www.rhsboating.com.au/brands-listing/category/t-h-marine-boat-catches-hardware-scuppers.html)

 [+](#)

 [–](#)

 The add to cart button will appear once you select the values above

    ### T-H Marine 12V 10A Adjustable Automatic Livewell Pump Timer Control Panel

Moulded black plastic panel with solid-state adjustable on/off timer. Three-way off/manual/auto switch. Suitable for retrofitting livewell/aerator systems. Maximum pump load: 10A.

### Choosing and using this product

This control is part of a pump system rather than a pump itself. It provides the stated switching or timing function, while the pump, power supply, circuit protection and plumbing must be selected separately. Match the controller to the actual pump voltage and current requirements before planning a retrofit. A pump's starting behaviour and the manufacturer's wiring requirements should be considered alongside its normal running current.

Choose a mounting position where the operator can see and reach the controls and where the wiring can be routed and supported properly. Check the panel or switch dimensions against the available space and confirm any cut-out details before drilling. Follow the current installation diagram for the particular controller and pump combination; do not assume wire colours or terminals match an older switch. Keep connections protected and accessible for inspection in accordance with the installation requirements.

Before putting the system into use, test each available mode and observe the pump's actual response. An automatic timer cycles the pump according to its settings; it does not measure the health of livebait or guarantee adequate circulation under every condition. Select settings around the tank, pump and operating conditions, then monitor the result. Test the timed livewell start and stop behaviour with the actual pump and water-supply arrangement rather than relying only on the switch position.

Inspect the installation periodically for loose connections, damage and changes in pump performance. Keep the control instructions with the boat's equipment records so another operator can understand the manual and automatic modes. If replacing a failed control, check the pump and circuit for the cause of the failure before fitting the new part. Electrical work should follow the equipment manufacturer's requirements and be checked by a suitably competent installer.

### Product details

- Product code: RWB6942.
- Product type: T-H Marine Livewell Automatic Controller - 12V.
- Panel: 83 x 83mm.
- Supply: 12V.